Forum for Excessive Sweating and Hyperhidrosis
Imprint

iontodevice.com
Iontophoresis vs. Hyperhidrosis

Buy an iontophoresis device

 Log inLog in SearchSearch

Forum for Iontophoresis Hyperhidrosis and excessive sweating

RegisterRegister  
 

Facial Sweat using Mask

 
Post new topic   Reply to topic    Hyperhidrosis Forum -> Iontophoresis
Author Message
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Fri Jan 20, 2017 11:57 am    Post subject: Facial Sweat using Mask Reply with quote

Dear all,

It has been noticed that many hand sweat treatment using Iontophoresis has caused palm skim to peel, just wonder if using Hidrex's Face Mask set can cause the face skin to peel?

And, what is the safe range in terms of Voltage and Current setting?


Looking forward to hearing a clarification or advice, thank you very much!

Best regards,
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Fri Jan 20, 2017 12:02 pm    Post subject: Reply with quote

Dear lioncity,

until now we have not heard of facial peeling do to use of the facial mask. As for the current setting, we recommend to start low and with a pulse width of 50%. Everyone has a different perception of current, so it is hard to recommend a specific setting. The important thing is that you don't feel pain.
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Fri Jan 20, 2017 1:06 pm    Post subject: Reply with quote

Thanks for your prompt reply.

Well, could yo please advise what is the reason to cause palm peeling using PSP1000? your advice is highly appreciated, I look forward to hearing from you, thank you.
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Fri Jan 20, 2017 1:41 pm    Post subject: Reply with quote

Skin peeling can occur if you drive too high settings for the current and dont hear to your bodys signals like pain or uncomfortable feelings
Also with bad devices and direct currents or bad pulsating current through lack of professional knowledge in the field iontophoresis engeneering
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Fri Jan 20, 2017 3:13 pm    Post subject: Reply with quote

Using PSP1000, if the output settings are set to a relatively low level without any painful feeling, can this ensure there will NO skin peeling even after a long time usage? please advise, thank you again!
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Fri Jan 20, 2017 3:20 pm    Post subject: Reply with quote

I have not heard of before
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Sat Jan 21, 2017 3:24 am    Post subject: Reply with quote

Palm skin peeling still can be acceptable, but if face has skin peeling, that will be a big issue.

At low current level with 50% pulse width, can this ensure face has not skin peeling even for long term use? this is my big concern, please kindly advise, I look forward to hearing the confirmation, thank you.
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Sat Jan 21, 2017 12:29 pm    Post subject: Reply with quote

As i mentioned before, if you have the false machine, or drive to high currents with ours , skin peeling can occur. I never heard of when the pulsed current is adjusted to a comfortable feeling
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Mon Jan 23, 2017 3:12 pm    Post subject: Reply with quote

If so, what is PSP1000's suggested current strength to avoid skin peeling? thank you again, I look forward to hearing from you.
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Mon Jan 23, 2017 4:01 pm    Post subject: Reply with quote

You have to find out, everyone is different. For the face be very careful and stop if you feel something like a tingling sensation, then go back a bit till you feel nothing
you can set the machine up like this -> https://www.iontodevice.com/hyperhidrosis/how-to-adjust-the-perfect-pulsed-setting-for-hidrex-psp1000-t748.html
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Tue Feb 07, 2017 4:22 am    Post subject: Reply with quote

Because facial mask is a whole piece, the current can go through from left to right side before putting it on face, is this the reason that the "Diving" indication doesn't work?

Please advise, thank you.
Back to top
View user's profile Send private message
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Tue Feb 07, 2017 3:44 pm    Post subject: Reply with quote

I am looking forward to an advice from the support team, thank you.
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Tue Feb 07, 2017 5:31 pm    Post subject: Reply with quote

No, this is another reason. You have to wetten the mask then you have to put in the electrodes, and THEN you plug the electrodes in, else the machine remains in security test mode

The dive indication is for service reasons and to prevent that someone setup zero volts and is wondering why the machine does not start (althoug she starts - but only counts up to 0)
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Wed Feb 08, 2017 4:02 am    Post subject: Reply with quote

After wettening the mask, putting in the electrodes, and then plugging the electrodes in with power on, then the Dive indication should be lightening, is it correct? before putting mask onto face?
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Wed Feb 08, 2017 12:54 pm    Post subject: Reply with quote

yes, exactly.
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Fri Feb 10, 2017 4:04 am    Post subject: Reply with quote

If Dive indication is lightening before putting onto face, then the Voltage will grow without control.

When you put mask onto face, the voltage might be growing to very high value already, which might hurt face. Is this a correct status?

Please advise, thank you.
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Fri Feb 10, 2017 11:47 am    Post subject: Reply with quote

the machine only goes as high as you have set it up in the beginning.
if you set for example 12 volts, then ater the DIVE light turns on, the machine automatically goes up until 12Volt. Maybe 1-2 less, but it will not go higher uncontrollably.
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Sun Feb 12, 2017 3:55 am    Post subject: Reply with quote

Hello Support,

Thanks for your replies. but it seems we are not talking the same point, sorry it's probably due to I didn't asked clearly.

My question is:
For example: I set 12 volts, then plug mask soaked with water into machine, then the DIVE light turns on before putting mask onto my face, the machine automatically goes up before putting mask onto my face.

Please note the statement "before putting mask onto my face"!

When after-a-while putting mask onto my face, the voltage might has been going up to 10V already, which might make my face uncomfortable!

How to handle this problem?
Back to top
View user's profile Send private message
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Tue Feb 14, 2017 3:01 am    Post subject: Reply with quote

I am still looking forward to hearing from support team, thanks !
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Tue Feb 14, 2017 1:32 pm    Post subject: Reply with quote

Ok, I understand and think I know where the error/problem is. Do everything as you have BUT, only insert one electrode in the designated pocket on the cheek of the mask. Then you can easily put the mask on and insert the other electrode in the designated pocket. ONLY THEN then the dive light should turn on and the machine starts the therapy, meaning that only then the volts start to go up.

Please let me know!
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Tue Feb 14, 2017 3:04 pm    Post subject: Reply with quote

Ok, I see, I will try the way as you advised, thank you!
Back to top
View user's profile Send private message
lioncity



Joined: 05 Aug 2015
Posts: 26

PostPosted: Thu Feb 16, 2017 3:11 am    Post subject: Reply with quote

So, this requires the 2nd electrode only can be inserted after the mask is put on the face?
Back to top
View user's profile Send private message
support
Site Admin


Joined: 20 Mar 2008
Posts: 3747

PostPosted: Thu Feb 16, 2017 12:46 pm    Post subject: Reply with quote

yes, or you plug the cable(s) in the device after you put the electrodes in the mask and the mask on the face
_________________
You are welcome...
Support Staff

Rental plan for iontophoresis

Buy your own home therapy iontophoresis device!

You can reach us from 9am to 5pm !Board time!
mail: info-at-iontophoresisdevice.com

Iontophoresis: WE CARE!
Back to top
View user's profile Send private message Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Excessive Sweating Forum -> Iontophoresis All times are GMT + 1 Hour
Page 1 of 1

 
Jump to:  
You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Users Memberlist